Hexagon Geospatial
MENU

Support WebGIS

Need a push in the right direction when configuring WebMap, Portal or SDI services? Looking for hints and tips, or just looking for Ideas and information? The WebGIS discussion board is where you start those discussions, connect and share information.
Showing results for 
Search instead for 
Do you mean 
Reply
Regular Contributor
Posts: 251
Registered: ‎10-12-2015
Accepted Solution

WebMap update 1 - no endpoint listening

Applying GeoMedia WebMap update 1.

 

From the readme:

Installation steps
--------------------

  1. Stop services:
    - IIS
    - GeoMedia WebMap
    - Geospatial Server Administration Console Service
    2. Run Setup.exe
    3.1 Run Install action and follow wizard, including WebMap Configuration
    3.2 Start services:
    - IIS
    - GeoMedia WebMap
    - Geospatial Server Administration Console Service
    3. Upgrade all instances in the Administration Console.

 

Following above sequence, when I go to run the configuration wizard I get:

WebmapUpdate1Configwizard.png

 

So shouldn't IIS be started prior to running the config wizard?

Technical Evangelist
Posts: 822
Registered: ‎09-11-2015

Re: WebMap update 1 - no endpoint listening

Hi Shaun,

 

I would think that Geospatial Server Administration Console should be running when WebMap Configuration Wizard runs, it uses that service internally.

IIS can be running too, but it's not required in order to configure the apps and app pools. It's safer to keep it offline as some of the services could get randomly requested, causing open handles on some files to be upgraded.

 

The upgrade instructions should be probably revalidated.

 

Thanks,

Jan

 

 

Jan Neumann
Post Sales Engineer Web Applications
Hexagon Geospatial

Technical Evangelist
Posts: 822
Registered: ‎09-11-2015

Re: WebMap update 1 - no endpoint listening

[ Edited ]

From my point of view, the upgrade instructions should be rather as follows:

 

  1. Stop services:
    - IIS
    - GeoMedia WebMap
    - Geospatial Server Administration Console Service
  2. Run Setup.exe
  3. After the installation completes, start service
    - Geospatial Server Administration Console Service
  4. Follow wizard, including WebMap Configuration
  5. Start services:
    - IIS
    - GeoMedia WebMap
  6. Upgrade all instances in the Administration Console.

EDIT: Please see another reply below...

Jan Neumann
Post Sales Engineer Web Applications
Hexagon Geospatial

Technical Evangelist
Posts: 822
Registered: ‎09-11-2015

Re: WebMap update 1 - no endpoint listening

I am testing the Update 1 installation now and I noticed that the Geospatial Administration Console Service was started automatically, by the installer. So, the update instructions are rather correct, but they follow an optimistic scenario.

 

It could be that your AdminConsole service failed to start. You might want to check Event Log for an explanation why the AdminConsole service didn't start.

Jan Neumann
Post Sales Engineer Web Applications
Hexagon Geospatial

Regular Contributor
Posts: 181
Registered: ‎10-26-2015

Re: WebMap update 1 - no endpoint listening

With the introduction of the "GeoMedia WebMap Publisher Remoting" Windows Service in the 2018 release, does this new service also need manually stopping prior to installing Update 1?

Regular Contributor
Posts: 251
Registered: ‎10-12-2015

Re: WebMap update 1 - no endpoint listening

I didn't notice anything in the event viewer.

 

I should mention I'm using the silent installer. With version 2016 the silent installer didn't run the config wizard right (perhaps for an update - I don't recall) so I run the silent installer without the config option then initiate the config wizard GeoMedia WebMap\ConfigWizard\ConfigurationWizard.exe via cmd/c. Not sure if that would make any difference - shouldn't. 

 

I'll update my script to start admin console and take the plunge with customers server. Let us know if others like Colins suggestion of remote need actioning as well.

Regular Contributor
Posts: 251
Registered: ‎10-12-2015

Re: WebMap update 1 - no endpoint listening

Looking at the Apollo install sequence (paraphrasing) ...

...

Stop the Geospatial Server Administration Console Service

Stop and restart the IISADMIN service, "IIS Admin Service"

Stop and restart the W3SVC service, "World Wide Web Publishing Service"

Install Patch

WARNING!!!: Check to be sure the Geospatial Server Administration Console Service is
running before proceeding with the Configuration Wizard.

Run the ERDAS APOLLO Configuration Wizard

 

 

Do you need immediate support?
If you encounter a critical issue and need immediate assistance please submit a Service Request through our Support Portal.